Monday, December 24, 2018

Finishing NP 10975 - Rapido Northern Pacific 10000-series Double Sheathed Box Cars, Part 2

I posted a brief writeup of the Rapido Northern Pacific 10000-series double sheathed box car almost two months ago (link to that post here). Since that time, I have made a few upgrades to that model and painted, lettered, and weathered it. This post describes the details associated with all of that. As I stated in the original post, it is an extremely fine model right out of the box. The changes highlighted here are ones that simply suit my tastes.


Most of the upgrades were performed on the ends, with the majority of those specifically on the B end. I replaced the running board supports with styrene to create more realistic details. I replaced the original retainer with a Precision Scale retainer valve with 0.008" wire "pipe". The brake staff was secured to a pivot support. Finally, I reworked the push pole pockets to create a more dished, stamped look, as on the prototype.


On the A end and the doors, I replaced the handles with ones fashioned from 0.010" wire, filed flat on the outer surface. The last upgrade was the replacement of the stock wheelsets with 0.088" tread width sets with 1.005" long axles.


The preparation and painting of the model followed my normal regimen. All metal and engineering plastic surfaces were lightly blasted with 200-grit aluminum oxide. I primed all surfaces, using Tamiya surface primer for the first time (link to my thoughts on it here). I painted the sides Rust (no. 4675) from the Model Master Acrylic line of paints. I masked the sides and painted the roof, ends, underframe, truck sideframes, and wheelsets Tamiya acrylic flat black. In preparation for decaling, I applied a light coat of Future (now Pledge) floor wax, creating a glossy surface.

I lettered the car* using decals I created myself and had printed by PDC of Canada specifically for this model. I reserved part of the capacity data, the reweigh location, the brake test, and repack stencils to be added during the weathering process. I also added a few chalkmarks prior to weathering.


I weathered the model using PanPastel and Bragdon powders. On the roof, ends, and underframe, I used brown, light grey, and Payne's grey. On the roof, I also interspersed this with some "blobs" of light grey paint applied with a Q-tip to simulate the beginnings of paint failure on some of the panels. I used the same powders on the sides, but applied them progressively: first, I applied small pieces of masking tape over the stencil areas referenced in the previous paragraph followed by powders that were then sealed with clear flat. I removed the masking from capacity, reweigh, and brake test stencils and added those along with more chalkmarks, another clear flat coat, followed by more weathering and yet another clear flat coat. Lastly, I added the repack stencils and more chalkmarks. Everything was sealed with a final flat coat.


Rapido has produced a beautiful model of a very significant prototype that belongs on most layouts. Bravo and I can't wait to see what is next from north of the border!

*the lettering layout doesn't exactly follow the standards for this car. The arched Northern Pacific and capacity data are slightly shifted to reflect photos of car NP 10975. Variations in the layout of lettering on actual equipment are not uncommon... remember, the shop crews were humans, not robots!

Thursday, December 6, 2018

Airbrushing - getting started



Airbrushing is one of the tools at the gateway to advanced modeling. However, many of us who have never experimented with using an airbrush look at it as a skill shrouded in mystery, requiring some innate talent and/or voodoo. Nothing could be further from the truth, particularly for the painting most model railroaders do, with single (or maybe two) colors with minimal masking and no real embellishments (if you really want to be impressed, look at some of the World War II aircraft schemes, including Luftwaffe schemes with various blotches/mottling or the Italian scheme with green “smoke ring” camouflage - link to decal for the less adventurous who don’t want to airbrush these devils, but illustrates what military modelers can do!) For what we as railroad modelers do it is simply a matter of spraying paint.

First, the intent of this post is to recommend a quality, but reasonably priced airbrush. I own and use an Iwata Medea N4500 Neo Gravity Feed airbrush. New ones can be found on eBay for approximately $50. It is extremely well-made and uses metal parts rather than plastic (an important consideration for me). It is a “double action” airbrush, meaning that the “trigger” controls both air and paint flow. This is a little more complicated than a single action airbrush, but I started using a double action airbrush when I was 10 years old and never felt like it was too difficult. I am certain you can learn to use it easily too. The one other thing I will say that is attractive to me about this model is that it disassembles easily, allowing the entire mechanism to be cleaned hassle-free. This is important because airbrush longevity and smooth operation requires a good cleaning regimen after each use. It takes only a few moments, but the impacts on operation are worth the diligence. One note: I have owned more expensive airbrushes, including the Iwata Revolution and Eclipse models and they are more difficult to clean and offer no advantages for the type of painting we do. My recommendation: buy the Neo and use the savings to invest in a quality airbrush compressor (buy an airbrush compressor and you won’t need earplugs because you’re trying to airbrush with that Campbell-Hausfield 100 HP compressor that you use to power your nail gun!)

If you’re read this far and are still curious, then take the plunge. All that’s required to learn is some paint (I recommend either Model Master acrylic or Tamiya acrylic paints,) thinner (most paints are too viscous out of the bottle; I thin these two brands using the manufacturers’ thinners at about 60% paint to 40% thinner,) an air source (I recommend this compressor,) and something to paint. To learn I suggest practicing on plain sheets of 0.040” white styrene. The point is to understand air pressure settings, distance from the object being painted, paint flow relative to the trigger, and how slowly or quickly to move the airbrush to avoid adding too much paint to one area at once. That’s it. I will post more in future on this topic, but it’s one of those things where it’s easier to learn by doing than reading.

Wednesday, December 5, 2018

Wordy Wednesday - Chicago, St. Paul, Minneapolis & Omaha Postwar AAR Box Car CMO 37836


In 1945, Chicago and North Western subsidiary Chicago, St. Paul, Minneapolis & Omaha purchased 400 AAR-design box cars of the postwar iteration from American Car & Foundry. The cars were assigned to series 37500-38298, even numbers. At first blush, the cars hewed closely to the design, with 10-panel riveted sides, Murphy rectangular panel roofs, 4/4 Improved Dreadnaught ends, and Youngstown corrugated (first 200 cars, shown here) or Superior panel steel doors (last 200 cars) and riding on ASF A-3 Ride Control trucks. Their most distinguishing characteristic was the Duryea Cushion underframe, with deep crossbearers that are visible in this photo, and Universal brake adjuster, a portion of which is also visible just to the right of the AB valve. However, the most interesting detail to me is the extreme compression of the truck springs (see below), no doubt due to a heavy load. It’s not something one sees often, let alone notices.


The photo is yet another low-angle, late-in-the-day flat light gem from Col. Chet McCoid that quite literally sheds light on so many details. Also note the gas storage tanks at both left and right. San Diego, California, November 19, 1954, Bob’s Photo


Thursday, November 29, 2018

Tamiya Liquid Surface Primer

Serendipity seems to make frequent visits to my hobby. Something I will be working on will make its way to the various lists that I follow, wholly unrelated to any activities or prompting by me. Such was the case within the last couple weeks. I recently purchased a bottle of the Tamiya primer shown in the photo above and within a couple days there was a discussion about primer and priming models on the Steam Freight Car list (my thoughts on that debate below). It is a rather thick surface preparation mixture, similar to the Mr. Surfacer products from Gunze-Sangyo (I am a raving fan of these products). When I looked at the bottle shown here, it noted that it could be thinned with Tamiya Lacquer thinner. I decided to give it a shot. I thinned it heavily with Dupont Lacquer Thinner, a premium thinner that I had purchased in a gallon container many years ago from an auto body repair shop. The ratio I used was about 60% thinner to 40% primer. I used it to prime an undecorated Rapido NP double sheathed box car. It sprayed beautifully, with excellent coverage and a flawless surface finish. It will be a go-to primer for my efforts.

On the subject of priming models, I fall decidedly into the yes category. A coat of primer does two things for me. It creates a neutral base that eases the coverage of the final color, be it freight car red or brown, some flavor or reefer yellow or orange, or even plain black. The other benefit is that it makes all details "pop" or stand out. This helps to reveal any and all surface defects and imperfections that need to be addressed prior to applying the main color(s).

Wednesday, November 28, 2018

Wordy Wednesday - Shell Filling Station


Shasta County, California. Filling stations close up as the tourist trade decreases, June, 1942, Lee Russell
As I begin my preparations for construction of a modest switching layout, I have been taking increased note of things that will be valuable references. It is little surprise that anything that will aid in my construction and detailing of structures and the scenes in which they’ll reside gets attention. I stumbled across this photo on the FSA-OWI photo site hosted by the Library of Congress. It is a defunct filling station in northern California (extreme northern, relatively close to Oregon, where I am modeling). Granted, the gasoline sales portion of the station and the accompanying equipment appeared to have been removed by the time this photo was recorded in 1942. Note that in the background at left is what to all appearances is a functioning gas station.

Nonetheless, there is still a great deal to be gleaned from this photo. Architecturally, the photo illustrates a large portion of the structure of the overhang that sheltered patrons while pumping gas. Details include the embellishments at the junctions of the roof line, support post beams and other areas. These were not only attractive features, but also served to tie together and strengthen the structure at critical points. As was quite common, the roof line of the shelter (and the shelter itself) was oriented to bisect the 90-degree angle created by the intersection of the streets.

Details abound. The large SHELL sign atop the shelter would be a great touch to add to a model, including the support wires, extending to the roof eaves. The Quaker State lube service sign is another add-on to accent the scene. Finally, while every window in this scene has one, likely due to the “hibernation” of the station’s gas dispensing operations, the signs promoting the Russell Bros. Circus in Redding (California) on June 27 are a great detail that adds “life” to this scene, and could be similarly replicated on a model, albeit in maybe one or two signs.

The great thing is that there are numerous commercially available 1920s vintage gas station kits that follow this general design, but that could be easily and minimally modified using a photo such as this one to make it “one’s own” so that visitors to the layout will appreciate its uniqueness rather than mentally noting that the gas station is the same one seen on many layouts. 

Monday, November 26, 2018

Completing the Kadee Santa Fe Class Bx-57 40' PS-1 Box Car



The first installment on the Kadee Santa Fe Bx-57 illustrated some of the changes effected to replicate the differences on the prototype. It is worth reiterating these major details. Of note, the Bx-57 class employed US Gypsum expanded metal brake steps and running boards, while the model was equipped with Apex Tri-Lok running boards and steps (Kadee has since produced the correct US Gypsum parts, resulting in a “drop-fit” replacement for the running boards; the brake step is a Plano etched metal part using the Kadee supports after carefully removing the Apex Tri-Lok step.) The Bx-57 also used the “upside-down” version of the Improved Youngstown door, while the model uses the more common version; a Southwest Scale door was substituted, along with scratchbuilt placard and route card boards. 
Kadee did replicate a few quirks of this class. Counter to usual Santa Fe practice, the Bx-57s did not have transverse-mounted brake reservoirs. Also, this class had the “SHIP AND TRAVEL Santa Fe all the way” slogan on the left side and the name train slogan on the right (Super Chief on this car) which was counter to Santa Fe painting and lettering practice. Kadee replicated these details faithfully, as well as the Royal Type F brake regulator, Ajax power hand brake, and ASF A-3 Ride Control trucks.
A note about the body color and paint matching is in order. As I replaced the door, I had to closely match the Kadee body color. I used three Tamiya colors to arrive at a satisfactory match. The mix is 50% Red, 25% Hull Red, and 25% Red Brown from the Tamiya acrylic line. As an aside, I love the ease with which Tamiya paints airbrush so this mixture will be my go-to Santa Fe Mineral Red-Brown for all future projects.
The brake test stencil on the reservoir
I replaced with wheelsets on the trucks with Kadee 0.088” tread width replacements. As I was modeling a car approximately 16 months old, I lightly weathered the car with a single application of Bragdon’s light gray powder, which mostly disappears under a clear flat coat (Tamiya). I added chalkmarks (a combination of pen and ink [a forthcoming post will cover this technique] as well as Speedwitch decal set D135) both before and after the weathering. I also applied a fresh paint patch over the repack stencil and added a late 1951 repack stencil. The door latch hardware (to the left of the doors) was salvaged from the original doors. I had to scrape off the ‘L’ and ‘R’ stencils to accommodate the door hardware so I added new ones from a Santa Fe box car decal set prior to weathering. I added a brake test stencil to the reservoir (even though I replaced the brake equipment, the original reservoir lacked this detail, too.)

After all of these subtle enhancements, I painted the angle cock/air hose parts black and gray. I added a final flat coat over everything. I polished the treads on the wheelsets, replaced them in the truck sideframes, and attached the trucks. Lastly, I added bits of paper for route cards. With that ATSF 31382 was ready for service. The PS-1 from Kadee remains one of the finest models ever produced in any scale. I look forward to adding a couple more from other roads to the fleet.

Wednesday, November 21, 2018

Wordy Wednesday - Union Starch & Refining - General American 1917-design Tank Car GATX 6719

Bob's Photo

General American 6719 is an interesting study. It was a General American 1917-design tank car built in January, 1921. It features many of the traits typical of the design, most notable the five “radial” courses to the tank. However, this car is different since it was modified to incorporate several changes. As expected, it was equipped with AB-schedule air brakes, replacing the KC-schedule brakes. Additionally, the expansion dome was fitted with a replacement safety manway and frangible disc vent. There is what may be a fitting or plug on the side of the dome. There are also what appear to be two patches, either as repairs or to strengthen parts of the bottom sheet of the tank. Finally, there was a chalkmark on the side of the tank noting, “syrup” which was undoubtedly a common load given that the car was leased by Union Starch & Refining, a producer of corn products, including corn syrup.


This car could be converted from a Tangent model using a safety manway from another manufacturer (Tangent, Tichy, Intermountain or others) and a frangible disc vent from Owl Mountain.
Photo by yours truly
Happy Thanksgiving!