Thursday, March 13, 2025

Clearing Up a Misperception

Santa Fe Caswell design GS gondola ATSF 171033 from class Ga- 5, Reading Yards, Rutherford, Pennsylvania,  June 19. 1947, Bob Charles Collection, Kalmbach Memorial Library 

There is a perception that GS gondolas (GS = "An Open Top Car, having fixed sides and ends and drop bottom, consisting of doors hinged at center sills to dump outside of rails," per the Official Railway Equipment Register) were West Coast cars and if you model the Northeast, Southeast, mid-Atlantic, etc., you don't have need for these on your layout*. I understand that notion. However, it is not correct. Granted, if you model western Massachusetts, for example, you should not have a gondola fleet comprised of 50% GS gons. That said, in a roster of solid bottom ("GB") gondolas, you could and would see GS gondolas from a variety of roads and should have a few in your fleet to mix into operating sessions. I have included some photos of GS gons in locales that support my contention (one shared by Richard Hendrickson and that I discussed with him on more than one occasion.)

C&EI 90108 was also of Caswell design, although it had received steel sheathing in place of the wood by the time it was photographed on February 10, 1952 in Columbus, Ohio, by Col. Chet McCoid. The doors were held in the "up" position using Wine door locks. Bob's Photo

Numerous fine models of GS gons have been offered over the years in both styrene and resin. The reason for and timing of this post is that I am working on a new pilot model for a styrene offering that one, is a GS-type gon like described in the previous paragraph, e.g. "western" GS gon, and two, is a fine example of contemporary HO scale technology, with fine tooling and separate details. Stay tuned for more about this model in the coming days...

Chicago & Illinois Western 1247 (ex-IC gon) was photographed in Aberdeen, North Carolina on October 30, 1951 by Col. Chet McCoid. Bob's Photo

The Burlington had a large fleet of composite GS gons that employed composite, Murphy or Dreadnaught ends. They also used Wine door locks. Note that there were not doors in all locations; from left, panels 2 and 4 had doors in the corresponding floor locations. Reading Yards, Rutherford, Pennsylvania, August 24, 1947, Bob Charles Collection, Kalmbach Memorial Library

*one caveat is that I am referring to and advocating for GS gons of the upper Midwest, Northwest, Mountain West, Southwest and West Coast; if you model western Massachusetts as the example I cited, you would quite likely see GS gons from the B&M, MEC or CN, as well, as they (and not too many other Eastern roads) did have modest fleets of GS gons 

Thursday, March 6, 2025

Interesting Armour Refrigerator Line Car Detail

ca. 1936, San Francisco, courtesy Bill Welch

Armour had a sizable fleet of refrigerator cars for the transportation of meat (in different stages of processing.) There were many cars like the one shown above, with steel center sill underframes with truss rods or pressed steel crossmembers. Armour also leased cars from Mather to augment the fleet and in the late 1940s, Armour added 2,000 all steel cars from AC&F to begin the shift to more contemporary design standards.

However, the purpose of this post is to highlight an unusual detail of these 11000-series cars. All of the other Armour wood reefers were equipped with typical sill steps that were attached to the bottom of the side and extended straight down from there although the right step usually had two rungs, like that shown here.) The rather interesting detail on the cars in the 11000 series is that they had two sharp 90 degree bends to nest around the bottom of the lower corner strap angle and side sheathing, as well as the common half twist, as can be seen. Crops of both sill steps are shown below to illustrate this feature. Yet another nuance to add to your Sunshine Models kit when you build it...